ath5k_hw_phy_init(9)

🌸 NAME 🌸

ath5k_hw_phy_init — Initialize PHY. This is the page for ath5k_hw_phy_init(9) in the Kernel API Manual, bestie ✨

✨ SYNOPSIS ✨

       int ath5k_hw_phy_init (struct ath5k_hw *ah , struct ieee80211_channel
       *channel , u8 mode , bool fast );

🎀 ARGUMENTS 🎀

• ah — The struct ath5k_hw
• channel — The struct ieee80211_channel
• mode — One of enum ath5k_driver_mode
• fast — Try a fast channel switch instead

🦋 DESCRIPTION 🦋

okay so this is the main function used during reset to initialize PHY, or to do a fast channel change if possible 💅 it’s giving “big reset energy” and “quick switch energy” at the same time, and honestly? iconic.

💅 NOTE 💅

🚨 bestie, Do not call this one from the driver, it assumes PHY is in a warm reset state ! 🚨

🔥 SEE ALSO 🔥

literally the whole extended friend group: 💖

• Kernel file ./drivers/net/wireless/ath/ath5k/phy.c PHY related functions(9)
• ath5k_hw_radio_revision(9)
• ath5k_channel_ok(9)
• ath5k_hw_chan_has_spur_noise(9)
• ath5k_hw_rfb_op(9)
• ath5k_hw_write_ofdm_timings(9)
• ath5k_hw_phy_disable(9)
• ath5k_hw_wait_for_synth(9)
• RF Gain optimization(9)
• ath5k_hw_rfgain_opt_init(9)
• ath5k_hw_request_rfgain_probe(9)
• ath5k_hw_rf_gainf_corr(9)
• ath5k_hw_rf_check_gainf_readback(9)
• ath5k_hw_rf_gainf_adjust(9)
• ath5k_hw_gainf_calibrate(9)
• ath5k_hw_rfgain_init(9)
• ath5k_hw_rfregs_init(9)
• ath5k_hw_rf5110_chan2athchan(9)
• ath5k_hw_rf5110_channel(9)
• ath5k_hw_rf5111_chan2athchan(9)
• ath5k_hw_rf5111_channel(9)
• ath5k_hw_rf5112_channel(9)
• ath5k_hw_rf2425_channel(9)
• ath5k_hw_channel(9)
• PHY Calibration routines(9)
• ath5k_hw_read_measured_noise_floor(9)
• ath5k_hw_init_nfcal_hist(9)
• ath5k_hw_update_nfcal_hist(9)
• ath5k_hw_get_median_noise_floor(9)
• ath5k_hw_update_noise_floor(9)
• ath5k_hw_rf5110_calibrate(9)
• ath5k_hw_rf511x_iq_calibrate(9)
• ath5k_hw_phy_calibrate(9)
• ath5k_hw_set_spur_mitigation_filter(9)
• Antenna control(9)
• ath5k_hw_set_def_antenna(9)
• ath5k_hw_set_fast_div(9)
• ath5k_hw_set_antenna_switch(9)
• ath5k_hw_set_antenna_mode(9)
• ath5k_get_interpolated_value(9)
• ath5k_get_linear_pcdac_min(9)
• ath5k_create_power_curve(9)
• ath5k_get_chan_pcal_surrounding_piers(9)
• ath5k_get_rate_pcal_data(9)
• ath5k_get_max_ctl_power(9)
• Power to PCDAC table functions(9)
• ath5k_fill_pwr_to_pcdac_table(9)
• ath5k_combine_linear_pcdac_curves(9)
• ath5k_write_pcdac_table(9)
• Power to PDADC table functions(9)
• ath5k_combine_pwr_to_pdadc_curves(9)
• ath5k_write_pwr_to_pdadc_table(9)
• ath5k_setup_channel_powertable(9)
• ath5k_write_channel_powertable(9)
• Per-rate tx power setting(9)
• ath5k_setup_rate_powertable(9)
• ath5k_hw_txpower(9)
• ath5k_hw_set_txpower_limit(9)

okay that’s the whole page, bestie 💖 the source/version footer says ./drivers/net/wireless/ath/ath5k, the date is October 2026, and it signs off as ath5k_hw_phy_init(9) 🎀✨🫶