📦 linuxcnc-uspace

286 pages · page 2 of 2

Q (continued)

R

  • rosekins(9)Kinematics for a rose engine✨
  • rotarydelta(1)Vismach Virtual Machine GUI✨
  • rotatekins(9)kinematics definitions for LinuxCNC For additional information, see the Documents 'Advanced Topics': Kinematics 5-Axis Kinematics Switchable Kinematics✨
  • rs274(1)standalone G-code interpreter✨
  • rtapi_app(1)creates a simulated real time environment✨

S

  • sample_hold(9)Sample and Hold✨
  • sampler(9)sample data from HAL in real time✨
  • scale(9)LinuxCNC HAL component that applies a scale and offset to its input✨
  • scaled_s32_sums(9)Sum of four inputs (each with a scale)✨
  • scaragui(1)Vismach Virtual Machine GUI✨
  • scarakins(9)kinematics definitions for LinuxCNC For additional information, see the Documents 'Advanced Topics': Kinematics 5-Axis Kinematics Switchable Kinematics✨
  • schedrmt(1)telnet based scheduler for LinuxCNC✨
  • scorbot-er-3(1)to link the Intellitek Scorbot educational robot to LinuxCNC✨
  • select8(9)8-bit binary match detector✨
  • sendkeys(1)send input events based on pins or scancodes from HAL✨
  • serport(9)Hardware driver for the digital I/O bits of the 8250 and 16550 serial port.✨
  • setsserial(9)a utility for setting Smart Serial NVRAM parameters. NOTE: This rather clunky utility is no longer needed except for flashing new smart-serial remote firmware. Smart-serial remote parameters can now…✨
  • setup_designer(1)A script to configure the system for use of QTdesigner✨
  • shuttle(1)control HAL pins with the ShuttleXpress, ShuttlePRO, and ShuttlePRO2 device made by Contour Design✨
  • siggen(9)signal generator✨
  • sim-torch(1)A simulated plasma torch✨
  • sim_axis_hardware(9)A component to simulate home and limit switches✨
  • sim_encoder(9)simulated quadrature encoder✨
  • sim_home_switch(9)Home switch simulator✨
  • sim_matrix_kb(9)convert HAL pin inputs to keycodes✨
  • sim_parport(9)A component to simulate the pins of the hal_parport component✨
  • sim_pin(1)GUI for displaying and setting one or more HAL inputs✨
  • sim_spindle(9)Simulated spindle with index pulse✨
  • simple_tp(9)This component is a single axis simple trajectory planner, same as used for jogging in LinuxCNC.✨
  • simulate_probe(1)simulate a probe input✨
  • sphereprobe(9)Probe a pretend hemisphere✨
  • spindle(9)Control a spindle with different acceleration and deceleration and optional gear change scaling✨
  • spindle_monitor(9)spindle at-speed and underspeed detection✨
  • sserial(9)Smart Serial LinuxCNC HAL driver for the Mesa Electronics HostMot2 Smart-Serial remote cards✨
  • stepconf(1)A configuration wizard for parallel-port based machines.✨
  • stepgen(9)software step pulse generation✨
  • steptest(9)Used by Stepconf to allow testing of acceleration and velocity values for an axis.✨
  • streamer(9)stream file data into HAL in real time✨
  • sum2(9)Sum of two inputs (each with a gain) and an offset✨
  • supply(9)set output pins with values from parameters (obsolete)✨
  • svd-ps_vfd(1)HAL non-realtime component for SVD-P(S) VFDs✨

T

  • teach-in(1)jog the machine to a position, and record the state✨
  • thc(9)Torch Height Control✨
  • thcud(9)Torch Height Control Up/Down Input✨
  • thermistor(1)compute temperature indicated by a thermistor✨
  • threads(9)creates hard realtime HAL threads✨
  • threadtest(9)LinuxCNC HAL component for testing thread behavior✨
  • time(9)Time on in Hours, Minutes, Seconds✨
  • timedelay(9)The equivalent of a time-delay relay✨
  • timedelta(9)LinuxCNC HAL component that measures thread scheduling timing behavior✨
  • tof(9)IEC TOF timer - delay falling edge on a signal✨
  • toggle(9)'push-on, push-off' from momentary pushbuttons✨
  • toggle2nist(9)toggle button to nist logic✨
  • ton(9)IEC TON timer - delay rising edge on a signal✨
  • tool_mmap_read(1)A component of the tool database system (an alternative to the classic tooltable)✨
  • tool_watch(1)A component of the tool database system (an alternative to the classic tooltable)✨
  • tooledit(1)tool table editor✨
  • touchy(1)TOUCHY LinuxCNC Graphical User Interface✨
  • tp(9)IEC TP timer - generate a high pulse of defined duration on rising edge✨
  • tpcomp(9)Trajectory Planning (tp) module skeleton✨
  • tripodkins(9)kinematics definitions for LinuxCNC For additional information, see the Documents 'Advanced Topics': Kinematics 5-Axis Kinematics Switchable Kinematics✨
  • tristate_bit(9)Place a signal on an I/O pin only when enabled, similar to a tristate buffer in electronics✨
  • tristate_float(9)Place a signal on an I/O pin only when enabled, similar to a tristate buffer in electronics✨
  • trivkins(9)kinematics definitions for LinuxCNC For additional information, see the Documents 'Advanced Topics': Kinematics 5-Axis Kinematics Switchable Kinematics✨

U

  • update_ini(1)converts 2.7 format INI files to 2.8 format✨
  • updown(9)Counts up or down, with optional limits and wraparound behavior✨
  • userkins(9)Template for user-built kinematics✨

V

  • vfdb_vfd(1)HAL non-realtime component for Delta VFD-B Variable Frequency Drives✨
  • vfs11_vfd(1)HAL non-realtime component for Toshiba-Schneider VF-S11 Variable Frequency Drives✨

W

X