📦 libgpib-doc

86 pages

A

AllSPoll(3)serial poll multiple devices✨
AsyncIbcnt(3)ibcnt, ibcntl values for last asynchronous I/O operation✨
AsyncIberr(3)iberr value for last asynchronous I/O operation✨
AsyncIbsta(3)ibsta value for last asynchronous I/O operation✨

C

CFGn(3)generate 'configure n meters' command byte✨

D

DevClear(3)clear a device✨
DevClearList(3)clear multiple devices✨

E

EnableLocal(3)put devices into local mode.✨
EnableRemote(3)put devices into remote mode.✨

F

FindLstn(3)find devices✨
FindRQS(3)find device requesting service and read its status byte✨

G

GetPAD(3)extract primary address from an Addr4882_t value✨
GetSAD(3)extract secondary address from an Addr4882_t value✨

I

ibask(3)query configuration (board or device)✨
ibbna(3)change access board (device)✨
ibcac(3)assert ATN (board)✨
ibclr(3)clear device (device)✨
ibcmd(3)write command bytes (board)✨
ibcmda(3)write command bytes asynchronously (board)✨
ibcnt(3)hold number of bytes transferred, or errno✨
ibconfig(3)change configuration (board or device)✨
ibdev(3)open a device (device)✨
ibeos(3)set end-of-string mode (board or device)✨
ibeot(3)assert EOI with last data byte (board or device)✨
iberr(3)holds error code✨
ibevent(3)get events from event queue (board)✨
ibfind(3)open a board or device (board or device)✨
ibgts(3)release ATN (board)✨
ibist(3)set individual status bit (board)✨
iblines(3)monitor bus lines (board)✨
ibln(3)check if listener is present (board or device)✨
ibloc(3)go to local mode (board or device)✨
ibonl(3)close or reinitialize descriptor (board or device)✨
ibpad(3)set primary GPIB address (board or device)✨
ibpct(3)pass control (board)✨
ibppc(3)parallel poll configure (board or device)✨
ibrd(3)read data bytes (board or device)✨
ibrda(3)read data bytes asynchronously (board or device)✨
ibrdf(3)read data bytes to file (board or device)✨
ibrpp(3)perform a parallel poll (board or device)✨
ibrsc(3)request system control (board)✨
ibrsp(3)read status byte / serial poll (device)✨
ibrsv(3)request service (board)✨
ibrsv2(3)request service (board)✨
ibsad(3)set secondary GPIB address (board or device)✨
ibsic(3)perform interface clear (board)✨
ibspb(3)obtain length of serial poll bytes queue (device)✨
ibsre(3)set remote enable (board)✨
ibsta(3)holds status✨
ibstop(3)abort asynchronous i/o operation (board or device)✨
ibtmo(3)adjust io timeout (board or device)✨
ibtrg(3)trigger device (device)✨
ibvers(3)Obtain the current linux gpib version.✨
ibwait(3)wait for event (board or device)✨
ibwrt(3)write data bytes (board or device)✨
ibwrta(3)write data bytes asynchronously (board or device)✨
ibwrtf(3)write data bytes from file (board or device)✨

M

MakeAddr(3)pack primary and secondary address into an Addr4882_t value✨
MLA(3)generate 'my listen address' command byte✨
MSA(3)generate 'my secondary address' command byte✨
MTA(3)generate 'my talk address' command byte✨

P

PassControl(3)make device controller-in-charge✨
PPE_byte(3)generate 'parallel poll enable' command byte✨
PPoll(3)parallel poll devices✨
PPollConfig(3)configure a device's parallel poll response✨
PPollUnconfig(3)disable devices' parallel poll response✨

R

RcvRespMsg(3)read data✨
ReadStatusByte(3)serial poll a device✨
Receive(3)perform receive addressing and read data✨
ReceiveSetup(3)perform receive addressing✨
ResetSys(3)reset system✨

S

Send(3)perform send addressing and write data✨
SendCmds(3)write command bytes onto bus✨
SendDataBytes(3)write data✨
SendIFC(3)perform interface clear✨
SendList(3)write data to multiple devices✨
SendLLO(3)put devices into local lockout mode✨
SendSetup(3)perform send addressing✨
SetRWLS(3)put devices into remote with lockout state✨

T

TestSRQ(3)query state of SRQ bus line✨
TestSys(3)perform self-test queries on devices✨
ThreadIbcnt(3)thread-specific ibcnt, ibcntl values✨
ThreadIberr(3)thread-specific iberr value✨
ThreadIbsta(3)thread-specific ibsta value✨
Trigger(3)trigger multiple devices✨

W

WaitSRQ(3)sleep until the SRQ bus line is asserted✨