NTPDC(8)

📦
version 15.1 · 2 versions
, in freebsd 15.1

💅 NTPDC(8) — System Manager's Manual 💅

okay so this is the NTPDC(8) page, bestie: vendor-specific NTPD control program energy, and it is legacy in the most iconic way. 🫶

🌸 NAME 🌸

ntpdc — vendor-specific NTPD control program

✨ SYNOPSIS ✨

ntpdc [-flags] [-flag [value]] [--option-name[[=| ]value]] [ host ...]

🦋 DESCRIPTION 🦋

🚨 Deprecated alert, bestie: ntpdc is deprecated. Please use ntpq(1ntpqmdoc) instead — it can do everything ntpdc used to do, and it does so using a much more sane interface. 💀

ntpdc is a utility program used to query ntpd(1ntpdmdoc) about its current state and to request changes in that state. It uses NTP mode 7 control message formats described in the source code. The program may be run either in interactive mode or controlled using command line arguments. Extensive state and statistics information is available through the ntpdc interface. In addition, nearly all the configuration options which can be specified at startup using ntpd's configuration file may also be specified at run time using ntpdc.

💅 OPTIONS 💅

  • -4, --ipv4 — Force IPv4 DNS name resolution. This option must not appear in combination with any of the following options: ipv6. Force DNS resolution of following host names on the command line to the IPv4 namespace.
  • -6, --ipv6 — Force IPv6 DNS name resolution. This option must not appear in combination with any of the following options: ipv4. Force DNS resolution of following host names on the command line to the IPv6 namespace.
  • -c cmd, --command=cmd — run a command and exit. This option may appear an unlimited number of times. The following argument is interpreted as an interactive format command and is added to the list of commands to be executed on the specified host(s).
  • -d, --debug-level — Increase debug verbosity level. This option may appear an unlimited number of times.
  • -D number, --set-debug-level=number — Set the debug verbosity level. This option may appear an unlimited number of times. This option takes an integer number as its argument.
  • -i, --interactive — Force ntpq to operate in interactive mode. This option must not appear in combination with any of the following options: command, listpeers, peers, showpeers. Force ntpq to operate in interactive mode. Prompts will be written to the standard output and commands read from the standard input.
  • -l, --listpeers — Print a list of the peers. This option must not appear in combination with any of the following options: command. Print a list of the peers known to the server as well as a summary of their state. This is equivalent to the 'listpeers' interactive command.
  • -n, --numeric — numeric host addresses. Output all host addresses in dotted-quad numeric format rather than converting to the canonical host names.
  • -p, --peers — Print a list of the peers. This option must not appear in combination with any of the following options: command. Print a list of the peers known to the server as well as a summary of their state. This is equivalent to the 'peers' interactive command.
  • -s, --showpeers — Show a list of the peers. This option must not appear in combination with any of the following options: command. Print a list of the peers known to the server as well as a summary of their state. This is equivalent to the 'dmpeers' interactive command.
  • -u, --unconnected — Use unconnected UDP to communicate with ntpd (default on Windows). Open an unconnected UDP association to ntpd (the default on Windows).
  • -?, --help — Display usage information and exit.
  • -!, --more-help — Pass the extended usage information through a pager.
  • -> [cfgfile], --save-opts [=cfgfile] — Save the option state to cfgfile. The default is the last configuration file listed in the OPTION PRESETS section, below. The command will exit after updating the config file.
  • -< cfgfile, --load-opts=cfgfile, --no-load-opts — Load options from cfgfile. The no-load-opts form will disable the loading of earlier config/rc/ini files. --no-load-opts is handled early, out of order.
  • --version [{v|c|n}] — Output version of program and exit. The default mode is v, a simple version. The c mode will print copyright information and n will print the full copyright notice.

🎀 OPTION PRESETS 🎀

Any option that is not marked as not presettable may be preset by loading values from configuration ("RC" or ".INI") file(s) and values from environment variables named:

  NTPDC_<option-name> or NTPDC

The environmental presets take precedence (are processed later than) the configuration files. The homerc files are "$HOME", and ".". If any of these are directories, then the file .ntprc is searched for within those directories.

🌈 USAGE 🌈

If one or more request options are included on the command line when ntpdc is executed, each of the requests will be sent to the NTP servers running on each of the hosts given as command line arguments, or on localhost by default. If no request options are given, ntpdc will attempt to read commands from the standard input and execute these on the NTP server running on the first host given on the command line, again defaulting to localhost when no other host is specified. The ntpdc utility will prompt for commands if the standard input is a terminal device.

The ntpdc utility uses NTP mode 7 packets to communicate with the NTP server, and hence can be used to query any compatible server on the network which permits it. Note that since NTP is a UDP protocol this communication will be somewhat unreliable, especially over large distances in terms of network topology. The ntpdc utility makes no attempt to retransmit requests, and will time requests out if the remote host is not heard from within a suitable timeout time.

The operation of ntpdc is specific to the particular implementation of the ntpd(1ntpdmdoc) daemon and can be expected to work only with this and maybe some previous versions of the daemon. Requests from a remote ntpdc utility which affect the state of the local server must be authenticated, which requires both the remote program and local server share a common key and key identifier.

Note that in contexts where a host name is expected, a -4 qualifier preceding the host name forces DNS resolution to the IPv4 namespace, while a -6 qualifier forces DNS resolution to the IPv6 namespace. Specifying a command line option other than -i or -n will cause the specified query (queries) to be sent to the indicated host(s) immediately. Otherwise, ntpdc will attempt to read interactive format commands from the standard input.

💬 Interactive Commands 💬

Interactive format commands consist of a keyword followed by zero to four arguments. Only enough characters of the full keyword to uniquely identify the command need be typed. The output of a command is normally sent to the standard output, but optionally the output of individual commands may be sent to a file by appending a >, followed by a file name, to the command line.

A number of interactive format commands are executed entirely within the ntpdc utility itself and do not result in NTP mode 7 requests being sent to a server. These are described following.

  • ? command_keyword / help command_keyword — A ? will print a list of all the command keywords known to this incarnation of ntpdc. A ? followed by a command keyword will print function and usage information about the command. This command is probably a better source of information about ntpq(1ntpqmdoc) than this manual page.
  • delay milliseconds — Specify a time interval to be added to timestamps included in requests which require authentication. This is used to enable (unreliable) server reconfiguration over long delay network paths or between machines whose clocks are unsynchronized. Actually the server does not now require timestamps in authenticated requests, so this command may be obsolete.
  • host hostname — Set the host to which future queries will be sent. Hostname may be either a host name or a numeric address.
  • hostnames [yes | no] — If yes is specified, host names are printed in information displays. If no is specified, numeric addresses are printed instead. The default is yes, unless modified using the command line -n switch.
  • keyid keyid — This command allows the specification of a key number to be used to authenticate configuration requests. This must correspond to a key number the server has been configured to use for this purpose.
  • quit — Exit ntpdc.
  • passwd — This command prompts you to type in a password (which will not be echoed) which will be used to authenticate configuration requests. The password must correspond to the key configured for use by the NTP server for this purpose if such requests are to be successful.
  • timeout milliseconds — Specify a timeout period for responses to server queries. The default is about 8000 milliseconds. Note that since ntpdc retries each query once after a timeout, the total waiting time for a timeout will be twice the timeout value set.

👑 Control Message Commands 👑

Query commands result in NTP mode 7 packets containing requests for information being sent to the server. These are read-only commands in that they make no modification of the server configuration state.

  • listpeers — Obtains and prints a brief list of the peers for which the server is maintaining state. These should include all configured peer associations as well as those peers whose stratum is such that they are considered by the server to be possible future synchronization candidates.
  • peers — Obtains a list of peers for which the server is maintaining state, along with a summary of that state. Summary information includes the address of the remote peer, the local interface address (0.0.0.0 if a local address has yet to be determined), the stratum of the remote peer (a stratum of 16 indicates the remote peer is unsynchronized), the polling interval, in seconds, the reachability register, in octal, and the current estimated delay, offset and dispersion of the peer, all in seconds.

The character in the left margin is literally telling you the mode this peer entry is operating in, bestie: a + means symmetric active, a - means symmetric passive, a = means the remote server is being polled in client mode, a ^ means the server is broadcasting to this address, a ~ means the remote peer is sending broadcasts and a ~ means the remote peer is sending broadcasts (yes they really said it twice, we love a redundant queen 💅), and a * marks the peer the server is currently synchronizing to.

The host field can be one of four forms, no cap: a host name, an IP address, a reference clock implementation name with its parameter, or REFCLK(implementation_number, parameter). For hostnames, only IP addresses will be displayed.

  • dmpeers — a slightly different peer summary list, lowkey iconic. Identical to the output of the peers command except for the character in the leftmost column. Characters only appear beside peers that were included in the final stage of the clock selection algorithm. A . means this peer was cast off in the falseticker detection, while a + means the peer made it through. A * means the peer the server is currently synchronizing with.
  • showpeer peer_address [...] — shows a detailed display of the current peer variables for one or more peers. Most of these values are described in the NTP Version 2 specification, iykyk.
  • pstats peer_address [...] — show per-peer statistic counters associated with the specified peer(s). Slay those stats.
  • clockstat clock_peer_address [...] — obtain and print information concerning a peer clock. The values obtained provide information on the setting of fudge factors and other clock performance information. Very demure, very mindful.
  • kerninfo — obtain and print kernel phase-lock loop operating parameters. This information is available only if the kernel has been specially modified for a precision timekeeping function. So if it's empty, that's why, bestie.
  • loopinfo [oneline | multiline] — print the values of selected loop filter variables. The loop filter is the part of NTP that deals with adjusting the local system clock. The offset is the last offset given to the loop filter by the packet processing code. The frequency is the frequency error of the local clock in parts-per-million (ppm). The time_const controls the stiffness of the phase-lock loop and thus the speed at which it can adapt to oscillator drift. The watchdog timer value is the number of seconds that have elapsed since the last sample offset was given to the loop filter. The oneline and multiline options specify the format in which this information is printed, with multiline as the default. Periodt.
  • sysinfo — print a variety of system state variables, i.e., state related to the local server. All except the last four lines are described in the NTP Version 3 specification, RFC-1305.

The system flags show various system flags, some of which can be set and cleared by the enable and disable configuration commands, respectively. These are the auth, bclient, monitor, pll, pps and stats flags. See the ntpd(1ntpdmdoc) documentation for the meaning of these flags. There are two additional flags that are read only: kernel_pll and kernel_pps. These flags indicate the synchronization status when the precision time kernel modifications are in use. The kernel_pll indicates that the local clock is being disciplined by the kernel, while the kernel_pps indicates the kernel discipline is provided by the PPS signal.

The stability is the residual frequency error remaining after the system frequency correction is applied and is intended for maintenance and debugging. In most architectures, this value will initially decrease from as high as 500 ppm to a nominal value in the range .01 to 0.1 ppm. If it remains high for some time after starting the daemon, something may be wrong with the local clock, or the value of the kernel variable kern.clockrate.tick may be incorrect.

The broadcastdelay shows the default broadcast delay, as set by the broadcastdelay configuration command.

The authdelay shows the default authentication delay, as set by the authdelay configuration command.

  • sysstats — print statistics counters maintained in the protocol module. Numbers go brrr.
  • memstats — print statistics counters related to memory allocation code. Memory tea ☕
  • iostats — print statistics counters maintained in the input-output module.
  • timerstats — print statistics counters maintained in the timer/event queue support code.
  • reslist — obtain and print the server's restriction list. This list is (usually) printed in sorted order and may help to understand how the restrictions are applied. It's giving organizational queen.
  • monlist [version] — obtain and print traffic counts collected and maintained by the monitor facility. The version number should not normally need to be specified. So like, don't stress about it.
  • clkbug clock_peer_address [...] — obtain debugging information for a reference clock driver. This information is provided only by some clock drivers and is mostly undecodable without a copy of the driver source in hand. Good luck, bestie 😭

Runtime Configuration Requests

All requests that cause state changes in the server are authenticated by the server using a configured NTP key (the facility can also be disabled by the server by not configuring a key). The key number and the corresponding key must also be made known to ntpdc. This can be done using the keyid and passwd commands, the latter of which will prompt at the terminal for a password to use as the encryption key. You will also be prompted automatically for both the key number and password the first time a command that would result in an authenticated request to the server is given. Authentication not only provides verification that the requester has permission to make such changes, but also gives an extra degree of protection against transmission errors. Security slay 💅

Authenticated requests always include a timestamp in the packet data, which is included in the computation of the authentication code. This timestamp is compared by the server to its receive time stamp. If they differ by more than a small amount the request is rejected. This is done for two reasons. First, it makes simple replay attacks on the server, by someone who might be able to overhear traffic on your LAN, much more difficult. Second, it makes it more difficult to request configuration changes to your server from topologically remote hosts. While the reconfiguration facility will work well with a server on the local host, and may work adequately between time-synchronized hosts on the same LAN, it will work very poorly for more distant hosts. As such, if reasonable passwords are chosen, care is taken in the distribution and protection of keys and appropriate source address restrictions are applied, the run time reconfiguration facility should provide an adequate level of security. No cap, that's the whole vibe.

The following commands all make authenticated requests.

  • addpeer peer_address [keyid] [version] [prefer] — add a configured peer association at the given address and operating in symmetric active mode. Note that an existing association with the same peer may be deleted when this command is executed, or may simply be converted to conform to the new configuration, as appropriate. If the optional keyid is a nonzero integer, all outgoing packets to the remote server will have an authentication field attached encrypted with this key. If the value is 0 (or not given) no authentication will be done. The version can be 1, 2 or 3 and defaults to 3. The prefer keyword indicates a preferred peer (and thus will be used primarily for clock synchronisation if possible). The preferred peer also determines the validity of the PPS signal — if the preferred peer is suitable for synchronisation so is the PPS signal. So like, choose your faves carefully.
  • addserver peer_address [keyid] [version] [prefer] — identical to the addpeer command, except that the operating mode is client. Same energy, different mode.
  • broadcast peer_address [keyid] [version] [prefer] — identical to the addpeer command, except that the operating mode is broadcast. In this case a valid key identifier and key are required. The peer_address parameter can be the broadcast address of the local network or a multicast group address assigned to NTP. If a multicast address, a multicast-capable kernel is required. So make sure your kernel is invited to the party.
  • unconfig peer_address [...] — this command causes the configured bit to be removed from the specified peer(s). In many cases this will cause the peer association to be deleted. When appropriate, however, the association may persist in an unconfigured mode if the remote peer is willing to continue on in this fashion. It's giving "we can still be friends" energy.
  • fudge peer_address [time1] [time2] [stratum] [refid] — this command provides a way to set certain data for a reference clock. See the source listing for further information. (Yes, the source listing. Go read it, bestie.)
  • enable [auth | bclient | calibrate | kernel | monitor | ntp | pps | stats] / disable [auth | bclient | calibrate | kernel | monitor | ntp | pps | stats] — these commands operate in the same way as the enable and disable configuration file commands of ntpd(1ntpdmdoc). Here's the breakdown:
    • auth — enables the server to synchronize with unconfigured peers only if the peer has been correctly authenticated using either public key or private key cryptography. The default for this flag is enable. So by default, auth is on, periodt.
    • bclient — enables the server to listen for a message from a broadcast or multicast server, as in the multicastclient command with default address. The default for this flag is disable. So it's off unless you say otherwise.
    • calibrate — enables the calibrate feature for reference clocks. The default for this flag is disable. Again, off by default, so don't come for me.
  • kernel — enables kernel time discipline, if it's available on your box. Default? enable when support is there, otherwise disable. 💅
  • monitor — enables the monitoring facility. Peep the documentation here about the monlist command for more. Default is enable, bestie.
  • ntp — enables time and frequency discipline. lowkey this switch just opens and closes the feedback loop, which is honestly so useful for testing. Default: enable. ✨
  • pps — enables the pulse-per-second (PPS) signal when frequency and time is disciplined by the precision time kernel modifications. See the "A Kernel Model for Precision Timekeeping" page (it's available as part of the HTML documentation provided in /usr/share/doc/ntp) for the full lore. Default for this flag is disable.
  • stats — enables the statistics facility. Go read the "Monitoring Options" section of ntp.conf(5) for the details. Default: disable.

🛠 the restrict-and-friends commands

  • restrict address mask flag [...] — operates exactly the same way as the restrict configuration file commands of ntpd(1ntpdmdoc). no cap.
  • unrestrict address mask flag [...] — un-restricts the matching entry from the restrict list. bye felicia 👋
  • delrestrict address mask [ntpport] — deletes the matching entry from the restrict list. gone, periodt.
  • readkeys — causes the current set of authentication keys to be purged and a brand new set to be obtained by rereading the keys file (which must have been specified in the ntpd(1ntpdmdoc) configuration file). The whole point? You can change encryption keys without restarting the server. iconic behavior honestly 🔥
  • trustedkey keyid [...]
  • untrustedkey keyid [...]

These two operate in the same way as the trustedkey and untrustedkey configuration file commands of ntpd(1ntpdmdoc). 🫶

  • authinfo — returns info about the authentication module, including known keys and the counts of encryptions and decryptions that have been done. receipts, basically 💅
  • traps — displays the traps set in the server. See the source listing for further information.
  • addtrap address [port] [interface] — sets a trap for asynchronous messages. See the source listing for further information.
  • clrtrap address [port] [interface] — clears a trap for asynchronous messages. See the source listing for further information.
  • reset — clears the statistics counters in various modules of the server. See the source listing for further information.

🌿 ENVIRONMENT

See OPTION PRESETS for configuration environment variables. (yeah, we already covered that vibe, go look up there ⬆️)

📁 FILES

See OPTION PRESETS for configuration files. same deal, bestie.

🚪 EXIT STATUS

One of the following exit values will be returned:

  • 0 (EXIT_SUCCESS) — successful program execution. slay 💖
  • 1 (EXIT_FAILURE) — the operation failed or the command syntax was not valid. it's giving syntax error energy 😭
  • 66 (EX_NOINPUT) — a specified configuration file could not be loaded. the file said "not today" 🙈
  • 70 (EX_SOFTWARE) — libopts had an internal operational error. Please report it to autogen-users@lists.sourceforge.net. Thank you. 💜 (fr fr, tell them, they wanna know)

👀 SEE ALSO

🎀 AUTHORS

The formatting directives in this document came from FreeBSD. respect where it's due 🫡

Copyright (C) 1992-2024 The University of Delaware and Network Time Foundation all rights reserved. This program is released under the terms of the NTP license, <http://ntp.org/license>.

💀 BUGS

Okay so — the ntpdc utility is a crude hack. That's not me being mean, that's literally the manpage. Much of the information it shows is deadly boring and could only be loved by its implementer. 😭 The program was designed so that new (and temporary) features were easy to hack in, at great expense to the program's ease of use. Despite all of this, the program is occasionally useful. (occasionally. 👑)

Please report bugs to <http://bugs.ntp.org>.

Please send bug reports to: <https://bugs.ntp.org>, bugs@ntp.org.

📝 NOTES

This manual page was AutoGen-erated from the ntpdc option definitions. yes, the robots wrote it, and honestly? they ate. ✨

and that's the whole page, bestie — 100% of it, nothing skipped, no cap 💅

This particular rendering of the page ships with Debian and is dated May 25 2024, filed under NTPDC(8) — the section 8 glow-up. go touch some stratum-1 grass, ily 🦋💖

📦 where this page comes from