cnetz_sim(1)

💖 NAME 💖

cnetz_sim — bestie, this is the SIM card sim/sniffer situation, and the whole point of it is right here: http://osmocom-analog.eversberg.eu/docs/ ✨

It's a General Commands Manual page, which is giving very much "read me before you poke at your SIM" energy 🎀

✨ SYNOPSIS ✨

cnetz_sim [options] <command>

okay so it's cnetz_sim, then some options, then a command. That's the whole vibe check 🦋

🌸 General options 🌸

• -h, --help — this help, literally just the help 💅
• --config [~/]<path to config file> — hand it a config file to use 🫶 If it starts with ~/, the path lives in your home dir. Each line in the config file is one option, and ngl you must NOT put - or -- in there!
• -v, --verbose <level> | <level>,<category>[,<category>[,...]] | list — the verbose dial 🎚️ Use list to get a list of all levels and categories. Verbose level: a digit for the debug level (default = 3). Verbose level+category: level digit followed by one or more categories → if no category is specified, all categories are selected 👑
• -v, --verbose date — show the date with debug output 📅
• -s, --serial-device <device> — the serial device (default = /dev/ttyUSB0) 🔌
• -b, --baud-rate <baud> — serial baud rate (default = 9600) ⚡
• -w, --write-pdu <filename> — write PDU to file, sniffer only 🕵️♀️

🎀 SIM card simulator options 🎀

• -E, --eeprom <name> — stores and reads EEPROM data to/from a file 📁 The file is stored at "~/osmocom/analog/sim_<name>.eeprom". If the file dos not exit yet, the default values are used. Values are always overwritten with card data, if defined. (yes, "dos not exit" — we keep it exactly as it is, no cap 💀)
• -F, --futln <phone number> — give 7 digits subscriber ID (default = 2222001) ☎️
• --sicherung <security code> — card's security code for simple authentication (default = 3103) 🔐
• --kartenkennung <card ID> — card's ID. Not relevant! (default = 3) 🙈
• --sonder <special code> — special codes are used for service cards (default = 0) 🌈
• --wartung <maitenance code> — may define features of service cards (default = 65535) 🛠️
• -P, --pin <pin> | 0000 — give 4 .. 8 digits of pin 🫶 Use 0000 to disable. (default = 0000) This will also reset the PIN error counter and unlocks the card 🔓
• -D, --directory <location> <number> <name> [--directory ...] — give storage location 01 .. 80 📇 To erase, give "" as number and name. This option can be given multiple times for more entries ✨
• -A, --authenticate 0x... — give 64 Bit value for authentication response. (default = all bits 1) 🔥

👑 Commands are: 👑

• sniff — to passively sniff SIM card communication 🕵️♀️
• sim — to simulate a SIM card 🎭

Not me dropping a whole error blob in here 😭 bestie this is literally on the page, so here it is, character for character:

[0;33m[1;31mDOPTIONS[0;m[0;33m [1;31mERROR[0;m[0;33m options.c:302 Given command line option '--version' is not a valid option, use '-h' for help![0;m

🌟 SEE ALSO 🌟

The full documentation for [0;33m[1;32mDOPTIONS[0;m[0;33m is maintained as a Texinfo manual. If the info and [0;33m[1;32mDOPTIONS[0;m[0;33m programs are properly installed at your site, the command

info [0;33m[1;32mDOPTIONS[0;m[0;33m

should give you access to the complete manual 📖

and that's the whole page, bestie — signed, sealed, and it's giving cnetz_sim(1) 💖✨ slay, go read your Texinfo manual, periodt 🎀🦋