Config...icolcd(3pm)

💖 NAME 💖

Config::Model::models::LCDd::picolcd — bestie, this is the Configuration class LCDd::picolcd. that's it, that's the name, iconic behavior 💅

---

✨ DESCRIPTION ✨

Configuration classes used by Config::Model.

generated from LCDd.conf — yeah it's auto-generated, no cap, don't come for it 🙈

---

🎀 Elements 🎀

okay so here's the whole roster of settings, one by one, no skipping, we're doing all of them 💖

🌸 Backlight 🌸

Sets the initial state of the backlight upon start-up. Optional. Type boolean.

• upstream_default value: on

🌸 Brightness 🌸

Set the initial brightness. Works only with the 20x4 device. Optional. Type integer.

• upstream_default value: 1000

🌸 Contrast 🌸

Set the initial contrast. Optional. Type integer.

• upstream_default value: 1000

🌸 Key0Light 🌸

If Keylights is on, then you can unlight specific keys below: Key0 is the directional pad. Key1 – Key5 correspond to the F1 – F5 keys. There is no LED for the +/- keys. This is a handy way to indicate to users which keys are disabled. Optional. Type boolean.

• upstream_default value: on

🌸 Key1Light 🌸

Optional. Type uniline.

• default value: on

🌸 Key2Light 🌸

Optional. Type uniline.

• default value: on

🌸 Key3Light 🌸

Optional. Type uniline.

• default value: on

🌸 Key4Light 🌸

Optional. Type uniline.

• default value: on

🌸 Key5Light 🌸

Optional. Type uniline.

• default value: on

🌸 KeyRepeatDelay 🌸

Key auto repeat is only available if the picoLCD driver is built with libusb-1.0. Use KeyRepeatDelay and KeyRepeatInterval to configure key auto repeat.

Key auto repeat delay (time in ms from first key report to first repeat). Use zero to disable auto repeat. Optional. Type integer.

• upstream_default value: 300

🌸 KeyRepeatInterval 🌸

Key auto repeat interval (time in ms between repeat reports). Only used if KeyRepeatDelay is not zero. Optional. Type integer.

• upstream_default value: 200

🌸 KeyTimeout 🌸

KeyTimeout is only used if the picoLCD driver is built with libusb-0.1. When built with libusb-1.0, key and IR data is input asynchronously so there is no need to wait for the USB data. KeyTimeout is the time in ms that LCDd spends waiting for a key press before cycling through other duties. Higher values make LCDd use less CPU time and make key presses more detectable. Lower values make LCDd more responsive but a little prone to missing key presses. 500 (.5 second) is the default and a balanced value. Optional. Type integer.

• upstream_default value: 500

🌸 Keylights 🌸

Light the keys? Optional. Type boolean.

• upstream_default value: on

🌸 LinkLights 🌸

Link the key lights to the backlight? Optional. Type boolean.

• upstream_default value: on

🌸 LircFlushThreshold 🌸

Threshold in microseconds of the gap that triggers flushing the IR data to lirc. If LircTime_us is on, values greater than 32.767ms will disable the flush. If LircTime_us is off, values greater than 1.999938s will disable the flush. Optional. Type integer.

• upstream_default value: 8000

🌸 LircHost 🌸

Host name or IP address of the LIRC instance that is to receive IR codes. If not set, or set to an empty value, IR support is disabled. Optional. Type uniline.

• upstream_default value: 127.0.0.1

🌸 LircPort 🌸

UDP port on which LIRC is listening. Optional. Type integer.

• upstream_default value: 8765

🌸 LircTime_us 🌸

UDP data time unit for LIRC. On: times sent in microseconds (requires LIRC UDP driver that accepts this). Off: times sent in 'jiffies' (1/16384s) (supported by standard LIRC UDP driver). Optional. Type boolean.

• upstream_default value: off

🌸 OffBrightness 🌸

Set the brightness while the backlight is 'off'. Works only with the 20x4 device. Optional. Type integer.

• upstream_default value: 0

---

🔥 SEE ALSO 🔥

• cme — go touch it, it's the whole point bestie 🫶

---

and that's the whole page, we ate and left no crumbs 👑 this was generated by perl v5.40.1 dated 2025-03-04 — yes the date is old, she's vintage, she's a classic, we respect her 💜🦋🌸